Design walkthrough
Designing a 300-metre ROV propulsion system
Propulsion on a 300 m vehicle is four coupled decisions — thrust, layout, power delivery and sealing — and getting them in the wrong order is what produces a vehicle that works in a test tank and disappoints at depth.
Why 300 m is a natural design point
Three hundred metres covers most port, dam, hull, aquaculture and inshore survey work, and it is the depth at which a large amount of well-proven hardware is rated: brushless marine thrusters, aluminium watertight boxes, mid-range gland penetrators. That makes it a sweet spot where a capable vehicle can be built without moving into deep-rated components and their costs.
It also means the pressure boundary is not the hard part. At 300 m in seawater the gauge pressure is about 30.2 bar. Every component in the boundary must exceed that, and the system rating is the lowest one in the chain — but 300 m parts are readily available. The hard part at this depth is power delivery down a long tether.
Step one: thrust and layout
Size the horizontal thrusters from drag at the target speed, not from a catalogue. For a typical inspection-class frame of around 0.25 m² frontal area and a drag coefficient near 1.0, holding 2 knots needs roughly 14 kgf of thrust before margin, and about 21 kgf with a 50% allowance for current, tether and fouling.
The usual layout is four horizontal thrusters vectored at 45°, giving surge, sway and yaw from one set, plus one or two vertical units for heave. Remember that a vectored unit contributes only cos(45°) — about 71% — of its rated thrust to forward motion. Four 4 kgf units at 45° deliver about 11.3 kgf forward, which is short of the 21 kgf target; either move to a larger thruster class or accept a lower speed.
This is the point to decide between non-ESC and integrated-ESC units. Integrated puts the controller in the thruster: fewer parts inside the housing, less wiring through the bulkhead, faster to commission. Non-ESC keeps the controller inboard where it can be replaced, instrumented and chosen independently — which is what a platform expected to iterate should do.
Step two: bus voltage, decided by the tether
This is the decision that separates a 300 m vehicle from a 30 m one. Thrusters that behave perfectly on a bench misbehave at the end of 300 m of tether, and the cause is almost always voltage drop rather than the thruster.
Loop resistance is R = ρ × 2L / A. Copper at 1.724 × 10⁻⁸ Ω·m, a 300 m one-way run and a 2.08 mm² (14 AWG) conductor gives about 4.97 Ω round trip. At 10 A that is roughly 50 V of drop — more than a 48 V supply has to give. The vehicle simply will not run.
There are only three levers: thicker copper, higher voltage, or less current. Thicker copper makes the tether heavy, stiff and negatively buoyant, which then costs foam. Raising the bus voltage is nearly always the right answer, because for the same delivered power, doubling voltage halves the current and quarters the loss. High-voltage down the tether with conversion on the vehicle is the standard architecture for exactly this reason.
Whatever you choose, size the conductor against the stall current of all thrusters together, not the hover current. The moment every unit spools up at once is when the bus sags and the controller browns out.
Step three: sealing the propulsion runs
Each thruster cable is a hole in the pressure boundary. At 300 m, aluminium-bodied gland penetrators are appropriate and widely available; stainless bodies take the same threads deeper if the design might grow.
Size the gland on the cable jacket outer diameter measured with calipers, not on the conductor size. This is the single most common subsea leak cause and it is entirely avoidable. Specify FKM rather than NBR for bulkhead seals: they see more handling than any other seal on the vehicle, and they live in saltwater with periodic solvent cleaning.
Count entries early. Six thrusters plus lights, camera, sensors and tether can exhaust an end cap quickly, and discovering it after the housing is machined is expensive. A tube coupling with its own radial ports is usually cheaper than moving up a diameter.
Step four: what propulsion does to buoyancy
Every thruster adds mass and displaced volume, and so does every metre of the heavier tether the power budget just demanded. Six thrusters at 500 g each is 3 kg of added mass before cabling, mounts and penetrators.
Track that in the buoyancy budget from the start rather than discovering it at trim. The foam to offset it has to fit on the frame, and the deeper-rated grades that a growing depth requirement might demand lift less per litre — so a late change of depth rating can cascade into a frame that no longer has room for the foam it needs.
Propulsion, power, sealing and buoyancy are one problem. Any design that treats them as four sequential purchases produces a vehicle that needs rework.
Run the numbers. The method above is implemented in our free ROV thruster sizing calculator, which states its assumptions and what it does not model.
Sources & basis
What this is based on.
- Thrust, weight, voltage and 300 m depth ratings for the Blu-Thrust range, and penetrator body materials and ratings, as published in the Vebix Automation catalogue.
- Copper resistivity 1.724 × 10⁻⁸ Ω·m at 20 °C; conductor areas per ASTM B258.
- Hydrostatic pressure at 300 m calculated as ρgh at 1025 kg/m³ and 9.80665 m/s².
Published 16 August 2026. Last revised 16 August 2026. Corrections to sales@
Talk to an engineer
Building a 300 m platform?
Send the frame dimensions, target speed and tether length and we will come back with a propulsion set, the conductor sizing to feed it and the buoyancy consequence.
- sales@
vebixautomation.com - Phone
- +91 97028 20020