Comparison
Aluminium versus acrylic subsea enclosures
The two dominant pressure vessel materials for small underwater vehicles differ on far more than depth rating. Here is the head-to-head, and the cases where each is clearly right.
Depth rating: not a like-for-like number
An anodised aluminium tube holds a flat depth rating — typically 1,000 m across the diameter range — because the wall is thick enough that diameter is not the limiting term for the depths these vehicles work at.
Cast acrylic does not behave that way. Its rating falls as diameter and length increase, roughly from 250 m at small diameters down toward 20 m for the largest, longest tubes. This catches people out when scaling a design: moving from a 4-inch to a 6-inch acrylic housing to fit a bigger payload can quietly halve the depth the vehicle is rated for.
The practical consequence is that acrylic is a shallow-water material that happens to be transparent, and aluminium is a general-purpose material that happens to be opaque. If the operating envelope is deeper than a couple of hundred metres, the comparison is over before it starts.
Optical access is the one thing acrylic does that aluminium cannot
Full optical clarity through the tube wall is the entire case for acrylic, and where a payload needs it, nothing else will do. A camera that must see sideways through the housing, a light sensor, an optical communications head — these are acrylic applications.
But check whether the payload needs to see through the wall or only through the end. A forward-looking camera needs a window, not a transparent tube, and a window is available as an end cap on an otherwise aluminium housing: flat acrylic for shallow work, moulded polycarbonate dome for wide-angle and reduced drag, or a borosilicate glass flange cap where optical throughput and repeated servicing both matter.
The dome is worth understanding. A flat viewport refracts at the water-to-window interface, narrowing the effective field of view and introducing distortion at the edges; a dome port with the lens at its centre of curvature largely avoids both. For wide-angle inspection work that difference is significant.
Thermal behaviour matters more than teams expect
Aluminium conducts heat; acrylic effectively does not. On a housing containing a passive data logger this is irrelevant. On one containing a Jetson-class compute module, a power converter or a motor controller, it decides whether the electronics survive.
A sealed acrylic tube is a thermos. The heat has nowhere to go but into the trapped air, and the internal temperature climbs until the electronics throttle or fail. An aluminium tube couples that heat into effectively infinite cold water, and the usual design move — bonding the hot component to the tube wall with a thermal pad or a machined bracket — turns the whole housing into a heatsink.
If the payload dissipates more than a handful of watts continuously, that alone can decide the material.
Servicing, handling and the things that go wrong
Acrylic is brittle and notch-sensitive. It crazes under solvent exposure — including some of the cleaners used to remove marine growth — and it scratches. Repeated tightening against an acrylic sealing face can indent or crack it, so acrylic end caps suit infrequent disassembly rather than a service-every-cruise workflow. Clamping an acrylic tube directly to a rigid rail concentrates stress on a thin wall; purpose-made clamp sets exist for exactly this reason.
Aluminium tolerates handling, tolerates solvents, tolerates being clamped to a frame, and can be serviced repeatedly without the sealing faces degrading. Anodising protects it, but it is worth remembering that aluminium in seawater in electrical contact with dissimilar metals will corrode galvanically — so fastener and fitting materials need thought that acrylic does not require.
One genuine advantage of acrylic beyond optics: you can see inside. Spotting condensation, a displaced connector or the first sign of ingress through the wall is a real diagnostic benefit on a test platform.
How to choose
Choose acrylic when the payload must see out through the tube wall, the depth is comfortably within the rating for that diameter, the internal heat load is small, and the housing will not be opened often.
Choose aluminium when depth exceeds a couple of hundred metres, when the payload dissipates real power, when the housing is opened every deployment, or when the vehicle takes knocks — which covers most working platforms.
A common and sensible outcome is both: an aluminium main housing for compute, power and heat, and a small acrylic or domed-cap housing for the optical payload. There is no rule that a vehicle has one housing material.
Sources & basis
What this is based on.
- Depth ratings, materials, diameters and weights for the Blu-Sub acrylic and aluminium pressure vessel ranges as published in the Vebix Automation catalogue.
- Optical throughput figure of approximately 95% for the borosilicate glass flange end cap, as published in the same catalogue.
Published 16 August 2026. Last revised 16 August 2026. Corrections to sales@
Talk to an engineer
Specifying a housing?
Send the payload, the depth and the heat load and we will confirm material, diameter, end caps and the sealing set to go with them.
- sales@
vebixautomation.com - Phone
- +91 97028 20020